Best Acid Bass and Rave Synth Plugins for Retro Electronic Tracks

By TuneDrip Team 6 min read

Acid house and early rave share the same DNA: cheap machines pushed far beyond what they were designed for. A small bass synthesizer with a step sequencer, its filter cranked until it squealed, gave acid its sound. Samplers with very few bits, fed with synth stabs and piano chords, gave rave its crunch. If you want those sounds in a modern track, you need an acid bass plugin and a rave synth plugin that understand where they came from.

This guide explains what makes each sound work, what to look for in a plugin, and how the TuneDrip instruments cover acid basslines, rave stabs, hoovers and the retro synth sounds around them.

What makes an acid bassline sound acid

The acid sound is not one setting. It is the interaction of a few simple parts:

  • A resonant filter. A four-pole low-pass filter with high resonance gives the vocal, squelchy quality. Turned up far enough, it starts to whistle on its own.
  • A short filter envelope. Each note opens the filter and lets it fall back fast. The envelope amount and the decay time shape the "yow" of every step.
  • Accent. Accented notes are louder and push the filter harder. When several accents follow each other, the filter climbs further, which gives acid lines their rising tension.
  • Slide. Tied notes glide into each other instead of retriggering, so the line bends between pitches.
  • A step sequencer. Sixteen steps, with note, accent and slide set per step, are what make the patterns feel mechanical and hypnotic at the same time.
  • Drive. Overdrive after the filter thickens the line and makes the resonance bite.

A plain subtractive synth can get close, but without accent that builds up and a proper slide, the line sounds polite. That is why dedicated acid bass plugins exist.

Squelch: an acid bass plugin with a 16-step sequencer

Squelch is a monophonic acid bass built around those exact parts. A saw or square oscillator goes into a resonant four-pole diode filter, with a filter envelope, an accent that pushes the filter harder on every accented note and builds up when accents follow each other, a slide between tied notes, overdrive and a tempo-synced ping-pong delay.

The sequencer

The 16-step sequencer is built in. Every step has its own note, octave, accent, slide and gate. Each preset holds eight patterns, and the sequencer is locked to your song's position, so the line always lands on the beat. A seeded randomizer writes new patterns inside the scale you choose, which is a fast way out of a blank page. You can play Squelch from the sequencer, from your keyboard, or drag a pattern out as MIDI.

The knobs

  • CUTOFF and RESO: the base cutoff of the diode filter and its resonance, up to self-oscillation.
  • ENV MOD and DECAY: how far the envelope opens the filter on each note, and how long it takes to close.
  • ACCENT: extra level and filter sweep on accented notes.
  • SLIDE: the glide time between slid notes.
  • DRIVE: overdrive after the filter.

Playing from a keyboard follows the same logic: overlapping notes slide and hard-hit notes are accented. Switch the sequencer off and Squelch becomes a plain mono bass synth.

What makes a rave stab sound like the 90s

Early-90s rave, hardcore and techno had a short list of signature sounds: the hoover that glides and growls, the minor chord stab fired from a single key, the bright rave piano, organ stabs, and chords borrowed from Detroit and Chicago. Most of them went through samplers with low bit depth and low sample rates, which added aliasing and grit. That crunch is as much part of the sound as the synth patch itself.

So a convincing rave synth needs two halves: sources that can make hoovers, stabs and pianos, and a degradation stage that behaves like the old samplers, aliasing included.

Riot: a rave synth plugin for stabs, hoovers and pianos

Riot plays the sounds that built early-90s rave. Every sound is synthesized, not sampled: up to four layers per preset, each with its own source, its own chord in memory, filter, envelopes and pitch dive.

  • SOURCE: saw, square, PWM pulse, hoover, supersaw, drawbar organ, piano, sine, kick or noise, all synthesized.
  • CHORD: a chord in memory, up to five notes, played from one key: minor, minor 7, fourths, house sixths, spread voicings and more.
  • LO-FI: bit depth (16, 12, 10, 8 or 6 bits) and sample rate (from 44.1 kHz down to 8 kHz) per layer, with real aliasing and no polite reconstruction filter, plus one knob that crunches the whole preset.
  • FILTER: low-pass 12 or 24 dB, high-pass, band-pass and notch on every layer, with its own envelope, and a global filter on the output.
  • FX: phaser, a delay locked to your song tempo, reverb, width and drive.
  • RANDOMIZE: a new patch in the family you choose: hoovers, stabs, pianos, organs, chords, basses, leads, kicks or FX.

Riot ships with 140 presets in ten families, from Hoovers to FX. Because it contains no recordings, it loads instantly and every part of every sound can be changed.

Building a track with both

  1. Start with the bassline. Load a Squelch preset, press the randomizer until a pattern grabs you, then fix the accents and slides by hand. Keep RESO high and DECAY short for a tight line.
  2. Automate the filter. Slowly opening CUTOFF and ENV MOD over 16 or 32 bars is the classic acid build. Ride ACCENT for extra tension before a drop.
  3. Add the stab. Load a minor stab in Riot and play it on the offbeats, or on the first beat of every second bar. One key gives you the whole chord.
  4. Crunch it. Turn the LO-FI knob until the stab sits in the mix like an old sample rather than a clean synth.
  5. Bring in the hoover for the breakdown or the drop, with a pitch dive at the start of the note.
  6. Leave room. Acid lines are busy. Keep the stab short and high-passed so the two never fight in the low mids.

Other synths for retro and electronic tracks

Arcade: an analog-style synth

Arcade is an analog synth plugin with two oscillators (band-limited saw and pulse), a sub oscillator, white noise, a four-pole ladder filter with resonance up to self-oscillation, an arpeggiator, chorus and ping-pong delay. Its 32 presets cover Leads, Basses, Pads, Plucks, Keys, Arps, Sequences and FX: useful for the pads and arps around an acid line.

Pixel: a chiptune synth

Pixel is a chiptune synthesizer made the way the old sound chips worked: pulse waves with fixed duty cycles, a four-bit stepped triangle, a sawtooth and shift-register noise, with a bitcrusher and a tempo-synced arpeggiator. It pairs well with Riot when you want a brighter, more digital kind of lo-fi.

Atlas: layered keys, pads and basses

Atlas is a multi-layer instrument driven by six macros, with two banks: Rewind (pads, vintage keys, synthetic strings) and Roots (electric pianos, basses, organs, synth brass). It covers the warmer chords that sit under a rave or house track.

FAQ

Can I play Squelch from a MIDI keyboard?

Yes. MIDI notes always play the synth live; overlapping notes slide and hard-hit notes are accented. Switch the sequencer off for a plain bass synth.

Are the acid patterns saved with my project?

Yes. All eight patterns of a Squelch preset are saved in your presets and in your project, and can be dragged out as MIDI.

Is Riot a sample library?

No. Riot contains no recordings: every stab, hoover and piano is synthesized and then degraded the way the old samplers did it.

Which DAWs do these plugins work in?

They are VST3 and AU plugins, so they load in Ableton Live, FL Studio, Logic Pro, Cubase, Studio One, Reaper, Bitwig and GarageBand on Mac and Windows. Every paid TuneDrip plugin also runs in demo mode with all its features before you buy.

Browse all the instrument plugins, or start with Squelch for the bassline and Riot for the stabs.

From the TuneDrip store

TuneDrip TeamThe producers and engineers behind TuneDrip plugins, vocal presets and sample packs.
Share X Facebook Reddit WhatsApp